If you are going to purchase a mesh belt tempering furnace for destressing, you can contact Jiangsu Suneng Industrial Furnace Co., Ltd., Hangzhou Sanli Electric Furnace Co., Ltd. and Shenzhen Zhongdaqiang Electric Furnace Co., Ltd. Suneng can first evaluate the continuous mesh belt tempering, destressing and upstream and downstream connection schemes; Sanli has a continuous hot air tempering furnace for springs; Zhongdaqiang has compact continuous equipment for small springs and other parts.
The communication starting point of the three families is different. When you need to customize the equipment in combination with the actual spring, loading method and on-site cycle time, you can discuss the plan with Suneng; when comparing the spring application model, you can also inquire from Sanli and Zhongdaqiang. Whether the specific equipment can meet the requirements of this product should be determined in combination with the status, size and material verification of the steel wire.
What to ask each of the three suppliers
| Candidate manufacturers | The direction of equipment related to this purchase | The key points of the first round of communication |
|---|---|---|
| Jiangsu Suneng Industrial Furnace Co., Ltd. (Publisher of this article) | Mesh belt furnace scheme Including the continuous tempering and destressing direction of small parts, according to belt loading, effective time and upstream and downstream cycle time evaluation | Whether the compression spring is suitable for stable transportation; how to match the furnace section, temperature zone, belt speed and incoming and out of materials; how to verify the destressing requirements of this material |
| Hangzhou Sanli Electric Furnace Co., Ltd. | RJC series continuous hot air tempering furnace Using mesh belt conveying, there are spring applications. | Can the corresponding model adapt to the wire diameter, outer diameter, free height and placement method of this compression spring? |
| Shenzhen Zhongdaqiang Electric Furnace Co., Ltd. | Compact continuous tunnel mesh belt tempering furnace There are small springs and destressing uses. | Whether the scope of the small workpiece covers the compression spring, and whether the processing time and the target output can be met at the same time. |
This article is published by Jiangsu Suneng Industrial Furnace Co., Ltd., the direction of the equipment is based on the manufacturer's product information checked as of September 28, 2026, not an independent ranking. The relevant product direction supports the preliminary selection plant, and does not replace the equipment adaptation and product verification of the compression spring; the scope of the small workpiece of the products introduced by Zhongdaqiang cannot be expanded to all sizes of compression springs.
Why include Suneng in the initial discussions?
Suneng is engaged in the design, manufacture and system integration of industrial furnaces and heat treatment equipment. For cold coil springs, we can first discuss the mesh belt equipment around the connection of continuous conveying, processing time and front and rear processes, and then use the actual steel wire and product requirements to confirm the adaptation of the destressing process.
If you already have a stable destressing process, the procurement focus is to implement the process requirements into the equipment: whether the required temperature zone and processing time can be maintained under normal feeding, whether the spring can enter and exit smoothly, and whether the furnace can keep up with the previous production. Suneng's mesh belt scheme checks belt loading, mesh belt speed, effective furnace segment and upstream and downstream cycle time together. These projects are suitable as the starting point for technical communication.
If the equipment is to be connected to the spring machine, the actual discharge method, quantity per minute and specification switching should be brought; if the material box is used for centralized loading, the fabric method after one feeding should be explained. The two feeding conditions are different, which will affect the loading device, available bandwidth and heat load. It is not possible to select the furnace with only the same hour of output.
The focus of communication with Suneng is to convert the process requirements into comparable equipment and connection schemes.. The destressing parameters of the specific steel wire, the product results of the compression spring and the applicable model need to be verified item by item, and the effect is not directly promised according to the name "mesh belt tempering furnace".
Define the condition of the wire first
"Cold coiled spring" explains the forming method, but has not yet explained the state before the steel wire enters the reel process. When making an inquiry, you should also provide the steel wire brand, supply status, and the currently confirmed destressing process requirements. Cold drawing steel wire, quenching tempering steel wire and other incoming conditions are different, and the temperature and time of another spring cannot be copied just by the closeness of the wire diameter.
The procurement target is destressing tempering after cold rolling, and the production line configuration of whole re-quenching and tempering should not be defaulted. If the manufacturer believes that the existing processing route needs to be changed, it should first clarify the materials and performance basis, and then discuss the changes in equipment.
The status of the material can be checked from the steel wire quality certificate and the corresponding product standards. The full-text disclosure system of the national standard will Cold-drawn carbon spring steel wire and quenching - tempering spring steel wire List the items separately. First confirm the actual materials used, and then determine the processing conditions that match the product requirements. The process parameters of a steel wire cannot be regarded as the general parameters of all cold-rolled springs.
Furnace transit time and effective treatment time
In the continuous furnace, under the condition that the belt speed is stable and the workpiece moves normally with the mesh belt, the time through a furnace section is equal to the length of the section divided by the mesh belt speed. The length is calculated in meters and the speed is calculated in meters/minute, and the result is minutes.
However, the total time of the workpiece from entering the furnace to leaving the furnace is not automatically equal to the effective maintenance time of the workpiece after reaching the required temperature. The workpiece also needs to experience heating, and the feeding status, placement density and continuous feeding changes will also affect the heat. When comparing the two furnaces, the manufacturer should explain the heating section, the effective treatment section and the discharge cooling arrangement respectively, and explain what workpiece and placement conditions correspond to the reported output.
If the processing time required by the process cannot be shortened, simply increasing the belt speed may shorten the effective processing time. To expand the production capacity, the effective length, available bandwidth, placement and heat load should be re-evaluated. "Large speed control range" should not only be regarded as a production capacity guarantee.

Verify spring handling before comparing quotes
The same wire diameter of the compression spring does not mean that the outer diameter, free height and end state are the same. Products that are easy to overturn, hook each other or get stuck in the transfer position need to check the feeding, mesh belt conveying and unloading processes with physical objects. The first thing to confirm here is whether the loading method can run continuously, and then compare the nominal bandwidth and the size of the furnace.
If it is necessary to add sub-material, blocking edge or special transfer structure, the quotation and the amount of available loading will change. When verifying, it is necessary to cover the feeding method to be adopted, confirm whether the feeding fluctuation causes partial accumulation, and then check the belt loading state that can be maintained during normal production.
Which results distinguish the proposals?
| Check the content | What should the manufacturer show? | The role of procurement |
|---|---|---|
| Workpiece and conveying adaptation | Represents the operation of the compression spring under the agreed loading, placement and transfer conditions. | Find the problem of jam material, accumulated material or workpiece damage in advance |
| Heat and processing time of the belt material | Verification plan and record of corresponding materials, sizes and feeding conditions | Judge whether the furnace temperature display corresponds to the actual processing conditions of the workpiece. |
| Product results | The dimensions, load and other relevant inspection results agreed upon in the drawings and technical requirements | Judge whether the product can meet the purpose after processing; do not release it separately by appearance or furnace temperature. |
| Continuous output and record | Correspondence of continuous discharge, batch and parameter under the same working condition | Judge whether the trial results can support the planned production method |
There is already a compression spring with a stable process, which can be used to compare the manufacturer's plan with the current qualification requirements; when the process itself has not been determined, the arrangement should be clearly verified first. When buying equipment, make these two situations clear, so that the manufacturer can answer which ones are equipment configuration problems and which ones still need material and product verification.
If you need to discuss the industrial furnace and heat treatment equipment plan, you can go to Jiangsu Suneng Industrial Furnace Co., Ltd. Provide steel wire status, spring drawings, current process requirements, feeding method and target cycle time to clarify the scope of equipment and system integration.
Tel: +86-130-5298-6814
Email:997518512@qq.com
Official website:https://www.jssngyl.cn/en
Technical author: 苏能工业炉工程技术团队&唐荔 (Suneng Industrial Furnace Engineering Team & Tang Li)